Yolo26 version is newest.
The zip file contains two models of different sizes (S and L) and a simple workflow.
Basically, S is sufficient, but you can use whichever you prefer.
Mosaic Detection series is integrated. penis, pussy, and penetration can be detected simultaneously.
This model is Adetailer for i2i or inpaint. GameCG,ArtistCG,and other.
Detects a mosaic censorsip, and redraw. Use it in conjunction with Lora or prompt as you like.
Recommended for use with comfyui.
denoising strength: around 0.5 ⇒Adjust it so that you can draw it well.
It's important to write detailed prompts.
Differences from previous version ↓
Improved detection accuracy.
If the angle is from the front where the stomach can be seen, the detection range will be wider. !BBOX version only!
⇒Possible to drawing pubic_hair's on-off,stomach_bulge,x-ray,uterus, etc...
In that case,increase denoising strength.
!!Atention!!
This model was trained with yolo11, so don't forget to update ultralytics.
\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\
モザイク検出シリーズは統合されました。ペニス、マンコ、挿入を同時に検出できます。
このモデルはi2iまたはinpaint用のAdetailerです。ゲームCG、アーティストCGその他に。
モザイク修正を検出して再描画します。好みのLoraやプロンプトと合わせて使ってください。
Comfyuiでの使用を推奨
denoising strength:0.5前後 ⇒うまく描画できるように調整してください。
プロンプトは詳細に書いてください。
以前のバージョンとの違い ↓
1.検出精度の向上
2.お腹が見える正面からのアングルの場合、検出範囲が広くなります。!BBOX versionのみ!
⇒陰毛の有無、腹ボコ、透視、子宮などの描画が可能に。
その場合、denoising strengthを上げてください。
!!注意!!
このモデルはyolo11でトレーニングしたため、ultralyticsのアップデートを忘れずに。
Description
yolo26 version
FAQ
Comments (10)
I wasn't expecting an update!
Thank you very much! ♥
I think it will detect more reliably than the previous model. Enjoy!
The new version of the model works great; it can detect thin mosaics that v4 cannot detect. Thank you for the great work!
Awesome model, using for my use case and it still does not catch everything, but likely 90-95% of my pictures.
Prompt With Style V2 (Mikey)
NotImplementedError: Cannot copy out of meta tensor; no data!
How should I go about fixing this issue?
Try updating ComfyUI and nodes. If you still encounter errors, you can show the AI a screenshot of your workflow and ask it for help; it might be able to answer your question.
I’ve successfully fixed the previous error and got the workflow running. However, in the final generated images, the mosaic/censored area remains completely unchanged.
Are there any specific parameters I should adjust in ComfyUI?
DetailerDebug (SEGS)
RuntimeError: mat1 and mat2 shapes cannot be multiplied (2x3584 and 2816x1280)
How to solve this issue?
@amberlypitts2140 I'll answer assuming the model is working. If the denoise value is too low, it won't have any effect. If your value is around 0.1, try increasing it little by little until you see a change.
@amberlypitts2140 The DetailerDebug error occurs when using a model other than SDXL for Checkpoint. My workflow is designed for Illustrious or Noob. If you're using something else (like SD1.5), you'll need to change the "dual clip" setting.

